Frisco E-Bike

E-Bike Parts: chargers, batteries, controllers, brakes, tires and more

Replacement parts are where mistakes get expensive. Each category explains how to identify what you have (voltage, connector, size, mount) before you buy. If your bike is misbehaving and you are not sure which part is at fault, start with an E-Bike Assessment instead of guessing.

Bike tools organized on a workshop rack
Popular:
Or describe what you need and we will narrow it down.Get an Assessment

6 products

All e-bike parts

Filter, then open a product for our notes and the Amazon listing.

Filter

Clear all

Battery voltage

48V (11)36V (4)52V (3)
Mechanic working on bike components
E-Bike Battery Chargers

48V 3A Faster E-Bike Charger, 3-Pin XLR Plug (generic)

If your 48V pack has a 3-pin XLR charge port and you want to cut charging time, a 3A unit is the sensible upgrade over the stock 2A brick. It is still a slow rate in absolute terms, so it is easy on the cells, but it trims a couple of hours off a 15–20Ah pack. As with any generic charger, buy by the spec sheet: 54.6V output, 3A, XLR plug, correct pin-out. Make sure your battery's BMS is rated for at least 3A charge current (nearly all are) and that the original charger was also XLR, not a barrel.

Best for: 48V packs with an XLR port and 15Ah or more capacity · Commuters who charge twice a day · A faster spare when the stock 2A brick is too slow

View details & where to buy

Sold on Amazon

Hands-on bike repair work
E-Bike Battery Chargers

52V 2A E-Bike Charger, 3-Pin XLR Plug (generic)

A 52V pack needs a 58.8V charger, and the 3-pin XLR plug is the most common fitting on the 52V Hailong and rack packs sold to kit builders. Mixing this up with a 48V charger is a classic mistake: a 54.6V charger will leave a 52V pack permanently under-charged, while a 58.8V charger on a 48V pack is dangerous. This generic 2A unit is the slow-and-steady option; heavier packs may benefit from a 3A or 5A unit if the BMS allows it. Confirm the XLR pin assignment matches your battery before the first plug-in.

Best for: 52V Hailong or rack-mount packs with an XLR charge port · BBS02/BBSHD builds running 52V · Riders who lost or wore out the original 52V charger

View details & where to buy

Sold on Amazon

Tools hanging on a repair shop wall
Connectors & Plugs

Amass XT60 Connectors, 5 Pairs

The XT60 is the standard battery-to-controller plug on a huge number of kit bikes and budget e-bikes, and Amass is the original manufacturer whose yellow plugs the clones copy. Genuine Amass connectors have tighter tolerances and better gold plating, which matters on a connection carrying 20–30 amps. A pack of five pairs gives you spares for a battery swap, a controller change, or a repair after a melted plug. Soldering is required; use a hot iron, heavy wire and heat shrink, and if you are not comfortable soldering high-current leads, have a professional do it.

Best for: Replacing a melted or loose XT60 on a battery or controller lead · Conversion builders standardizing on one plug · Making extension or adapter leads

View details & where to buy

Sold on Amazon

Close-up of bicycle gears and chain
Wiring Harnesses

Julet 1T4 Main Wiring Harness (Display, Throttle, 2x Brake) (generic)

The 1T4 harness is the backbone of most Julet-connector kit bikes: one multi-pin plug into the controller splits into a 5-pin display lead, a 3-pin throttle lead and two 2-pin brake-sensor leads, all waterproof. When a connector corrodes or a lead gets crushed, replacing the whole harness is faster than repairing one branch. The trap is that 1T4 harnesses come in several pin counts at the controller end and with different lead lengths, so match the controller-side plug and count the pins before ordering. Take a photo of your old harness's plugs for comparison.

Best for: KT and similar kits with Julet waterproof connectors · Replacing a corroded or damaged main cable · Tidying up a conversion with bare-wire connections

View details & where to buy

Sold on Amazon

Electric bike handlebar and display detail
Wiring Harnesses

Julet 5-Pin Display Extension Cable, 30–60 cm (generic)

Raising the bars, fitting a longer stem or moving a display often leaves the cable an inch too short, and the Julet 5-pin extension is the fix. It is a male-to-female waterproof lead in the same keyed format as the display connector on most KT, Lishui and generic controllers. Lengths from 30 to 100 cm are sold; buy the shortest one that reaches so you are not stuffing loops of cable behind the head tube. The same 5-pin format is used by some throttles and lights, so double-check what the lead on your bike is actually feeding before you order.

Best for: Riders who raised the handlebars or changed stems · Cargo and long-tail conversions with long cable runs · Relocating the display to the center of the bar

View details & where to buy

Sold on Amazon

Electric bike handlebar and display detail
Connectors & Plugs

Julet Waterproof Connector Set, 2/3/4/5/6-Pin Pigtails (generic)

Julet (and the near-identical Higo) round waterproof connectors are the signal plugs used across kit bikes for throttles, brake sensors, PAS, displays and lights. A pigtail set gives you male and female leads with short wire tails in the common pin counts, so you can re-terminate a component that came with bare wires or splice in a matching plug after a connector breaks. They are not crimp-it-yourself connectors; you solder or crimp the wire tails to your component, then heat-shrink. Match the pin count and gender to the plug on the other side.

Best for: Re-plugging a throttle, brake or PAS lead with a broken connector · Adapting bare-wire components to a Julet harness · Kit builders keeping a selection on hand

View details & where to buy

Sold on Amazon

Quick finders

Jump straight to what fits your bike

Find a charger by battery voltage

The charger must match the pack: 36V → 42.0V, 48V → 54.6V, 52V → 58.8V output.

36V (1)48V (2)52V (1)

Find a battery by voltage

Match voltage first, then mount style and connector.

36V (1)48V (1)52V (1)

Find a controller by voltage

Controllers and displays are usually paired — confirm the protocol.

36V (1)48V (2)

Find a tire by size

Size is printed on the sidewall (e.g. 20×4.0, 26×4.0, 27.5×2.4, 700×38c).

20x4 (1)26x4 (1)27.5 (1)700c (1)

Find a tube by size

Match the tire size and the valve type (Schrader vs Presta).

20x4 (1)26 (1)26x4 (1)700c (1)

Brake pads by brake type

Pad shape depends on the caliper model — check yours before ordering.

disc (3)

By connector / plug

XT60, Anderson, Julet/Higo, DC barrel, XLR…

julet (3)xlr-3-pin (2)dc-barrel-5.5x2.1 (1)dc-barrel (1)julet-3-pin (1)xt60 (1)anderson (1)

Browse

E-Bike Parts by category

Grouped the way a shop is organized. Each category page has buying notes, compatibility tips and its own filters.

Electrical10 categories

E-Bike Batteries

3

Replacement and spare lithium packs — match voltage, mount and connector.

E-Bike Battery Chargers

4

Replacement chargers — voltage, amperage and plug type must match your pack.

E-Bike Controllers

3

The brain between battery, motor, throttle and display.

E-Bike Displays

3

LCD/LED displays and replacement screens matched to your controller protocol.

E-Bike Motors

2

Replacement hub and mid-drive motors and conversion kits.

Hub Motors

2

Front and rear geared/direct-drive hub motors and wheel kits.

Mid-Drive Components

2

Chainrings, kits and service parts for mid-drive systems.

Wiring Harnesses

2

Main cables and extension harnesses for display, throttle and brake sensors.

Connectors & Plugs

3

XT60/XT90, Anderson, Julet/Higo waterproof connectors and battery discharge plugs.

Replacement Screens

2

Screens and protective covers for common display models.

Controls2 categories

Throttles

3

Thumb and twist throttles — connector and voltage signal must match.

Pedal Assist Sensors

2

Cadence and torque sensors that tell the controller you are pedaling.

Brakes4 categories

E-Bike Brake Pads

3

Disc pads in the right shape and compound for heavier, faster e-bikes.

Brake Rotors

2

160/180/203 mm rotors — check mount type (6-bolt vs Centerlock).

Brake Levers

2

Mechanical and hydraulic levers, including e-bike levers with motor cut-off sensors.

Hydraulic Brake Components

3

Calipers, hoses, olives, bleed kits and mineral oil / DOT fluid.

Wheels & Tires5 categories

E-Bike Tires

4

E-bike rated tires with puncture protection in the common 20×4, 26×4, 27.5 and 700c sizes.

Inner Tubes

4

Schrader/Presta tubes, thorn-resistant and sealant-filled options.

Tubeless Components

2

Sealant, valves, rim tape and plugs for tubeless setups.

Wheels & Rims

2

Replacement wheels and rims, including motor-compatible dropout widths.

Spokes & Nipples

2

Spokes sized for hub-motor flanges and heavy e-bike loads.

Drivetrain6 categories

Cassettes

2

7–12 speed cassettes; freehub standard must match your wheel.

Freewheels

2

Thread-on freewheels common on hub-motor e-bikes (often 7-speed).

E-Bike Chains

2

E-bike rated chains with stronger plates; match your speed count.

Derailleurs

3

Rear derailleurs, hangers and shifters for common e-bike drivetrains.

Cranksets

2

Cranks, chainrings and bottom brackets — including PAS-compatible options.

Pedals

2

Flat, wide-platform and folding pedals with grip for commuting.

Cockpit & Comfort8 categories

E-Bike Lights

2

Headlights and taillights — battery-powered or wired to the main pack.

Fenders

3

Full-coverage and fat-tire fenders sized to your wheel and tire width.

Racks (Parts)

1

Front and rear rack hardware for commuter and cargo setups.

Kickstands

2

Heavy-duty single and double-leg stands rated for e-bike weight.

Seats & Saddles

2

Wide comfort saddles, suspension seats and replacement covers.

Seat Posts

2

Suspension and rigid posts — check diameter (27.2, 30.9, 31.6 mm).

Handlebars & Stems

2

Riser, swept-back and adjustable stems for a more upright fit.

Grips

2

Ergonomic and lock-on grips for numb-hand relief.

Buyer guides

Common problems