E-Bike Parts

Handlebars & Stems

Riser, swept-back and adjustable stems for a more upright fit.

If your wrists, neck or back hurt on the e-bike, the fix is usually the cockpit, not the saddle. A riser or swept-back bar, a taller or adjustable stem, or both can put you in a relaxed upright position that suits the way most people ride e-bikes. Bars and stems also get bent in crashes and replaced when upgrading from a folding bike's stock cockpit to something more comfortable. Swapping a bar and stem is an afternoon job, but plan it: the grips, levers, shifter, throttle and display all have to come off and go back on.

Fit is about diameters. The bar's center clamp is 25.4mm or 31.8mm on most bikes (35mm on some mountain bikes), and the stem must match it. The stem attaches to the fork steerer either as a threadless stem clamping a 1 1/8 inch steerer or as a quill stem inserted into a threaded fork (22.2mm quill on most), and those are not interchangeable; many folding e-bikes use a proprietary folding stem. The grip area is 22.2mm on nearly all flat and riser bars, which keeps grips, levers, shifters and throttles compatible.

Rise and sweep set comfort: more rise lifts the bars, more sweep relaxes the wrists. The practical limit is cable length; raising the bars may need longer hydraulic hoses, shift cables, and display or throttle extension cables. Confirm your clamp and steerer type on your bike before ordering. When in doubt, ask a shop to confirm cable lengths; an electrical extension cable costs little, while an overstretched hydraulic hose is a real hazard.

2 products

Shop handlebars & stems

Open a product for our full notes, pros and cons, and the link to its Amazon listing. We do not sell or ship products ourselves.

Handlebars & Stems

Adjustable Angle Stem, 1-1/8 Threadless, 31.8 mm Clamp (generic)

An adjustable stem is the quickest way to raise the bars and sit more upright, which is what most e-bike riders with wrist or neck discomfort want. These alloy stems clamp a 1-1/8 inch threadless steerer and a 31.8 mm bar (25.4 mm versions exist), and a single bolt lets you set the angle anywhere from flat to near vertical. They are heavier and slightly flexier than a fixed stem and the angle bolt must be torqued properly. Check your steerer diameter and bar clamp size before ordering; folding bikes often have a proprietary stem that these do not replace.

Best for: Riders who want a more upright position · Fitting a bike that feels too stretched out · Commuters adjusting reach without buying several fixed stems

View details & where to buy

Sold on Amazon

Man sitting on a bench beside an electric bike

Handlebars & Stems

Riser Handlebar, 31.8 mm, Swept-Back Comfort (generic)

Swapping a flat bar for a riser with a bit of back-sweep brings the grips up and toward you, relaxing the wrists and shoulders; on a commuter e-bike it can be the difference between a bike you ride and one you avoid. Generic alloy risers with 31.8 mm center clamps, around 680 mm width and 40–60 mm of rise are widely sold. The 22.2 mm grip sections accept standard grips, levers, shifters and throttles. Moving controls over is an afternoon job; be ready for cables and the display lead to come up short if you go much higher.

Best for: Riders who want a more upright position than a flat bar gives · Commuters with wrist and shoulder discomfort · Replacing a bent bar

View details & where to buy

Sold on Amazon

How to choose handlebars & stems

Bar clamp diameter

25.4mm or 31.8mm are common; measure the center of your bar or read the stamp. The stem must match.

Steerer type

Threadless (stem clamps around a 1 1/8 inch steerer) or quill (stem inserts into the fork). Check which your bike has.

Rise, sweep and width

More rise and sweep for upright comfort; width to suit your shoulders and any width limits for bike lanes or doorways.

Adjustable stem

Lets you change angle without swapping parts; check it is rated for e-bike use and torque the pivot bolt properly.

Cable slack

Verify brake hoses, shift cables and electrical cables have room for the new height; plan extensions if not.

Compatibility notes

Stem clamp diameter must match the bar; steerer type (threadless versus quill) must match the fork. Confirm on your bike.
Grip area is 22.2mm on flat and riser bars, so controls carry over; drop bars and some cruiser bars differ.
Folding e-bike stems are often proprietary; confirm with the bike maker.

Installation considerations

Transfer grips, levers, shifter, throttle and display to the new bar, keeping the cable routing tidy.
Torque stem bolts to the marked spec (often 5 to 6 Nm) in an alternating pattern; overtightening crushes bars.
Check that the bars turn lock to lock without pulling cables or hoses taut.
Re-aim the headlight and re-center the display after the swap.

Maintenance tips

Check stem and bar bolts periodically; loose cockpit bolts are dangerous.
Inspect adjustable stem pivots for play and retorque.
Replace any alloy bar that has been in a hard crash even if it looks straight.

Frequently asked questions

What bar diameter does my e-bike have?

Measure the bar at the stem clamp: 25.4mm or 31.8mm are most common. The size is often stamped on the bar near the clamp.

Can I raise my handlebars without new cables?

A little, using stem spacers or a modest riser; more than a couple of centimeters usually needs longer brake hoses or cables and electrical extension cables.

Are adjustable stems safe?

Quality adjustable stems are fine for e-bike use when torqued properly; cheap ones develop play. Check the rating and tighten the pivot to spec.

Quill or threadless?

If the stem clamps around the outside of the fork steerer with bolts, it is threadless; if a single bolt on top tightens a wedge inside the fork, it is quill. They are not interchangeable.

Will my grips and levers fit a new bar?

Yes on almost any flat or riser bar, which are 22.2mm at the grips. Confirm that unusual bars are the same.